Ivelink Ceramic Cartridge Heater 12V 40W 620 Hotend for 3D Printer Prusa Mendel(Pack of 5pcs)

Description
-Cartridge heaters is consist of a cylindrical stainless steel tube and thus provide a high corrosion prevention
-The heating wire inside which is wound onto a ceramic core
-The number of coils varies depending on the power, and provide a great uniform distribution of heat, which considerably increases the long life of the heater as well as prevents the oxidation of the heater wire even at high temperatures
-The solids, liquids, and gases need to be heated by cartridge heater, transmit heat quickly by conduction if the producer of the heat (the cartridge) is in direct contact with the heat sink (any solid, liquid, or gas)
-Widely used for manufacturing plastic and rubber parts in the car industry or in the food processing industry, etc

Application
-Semiconductor chamber heating
– Semiconductor wafer lead connection
-Semiconductor wire and die bonding
-Freeze protection and deicing of equipment in cold climates or applications
-Humidity Control
– Patient Comfort heating used in medical devices
-Mold die and platen heating
-Seal bars used in packaging equipment
-Test sample heating in gas chromatography

Package Included
5pc x 12V Cartridge Heater with 1m wiring

Product Features

  • Cartridge Heater Material: 304 Stainless Steel
  • Voltage: 12v, Power: 40w
  • Diameter: 6mm ; Length: 20mm
  • Package Contents: 5x Cartridge Heaters 12V with 1m wiring
  • Application : Reprap Prusa I3 3D Printer

Visit The Website For More Information…

Witbot Double V Slot stainless steel Passive Round wheel with Bearings Idler Pulley Gear Perlin Wheel 3D Printer parts ( Pack of 5pcs)

Specification::
Inner Diameter: 5mm
Outer Diameter: 24.39mm
Height: 10.23mm
Net Weight: 25g/pcs
Color: Silver

Package content:
5*Wheels with Bearing

Product Features

  • Test one by one, high quality
  • Inner Diameter: 5mm
  • Outer Diameter: 24.39mm
  • Height: 10.23mm
  • Durable and flexible

Visit The Website For More Information…

HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…

BIQU GT2 16Teeth 3mm Bore Aluminum Timing Belt Idler Pulley for 3D Printer 6mm Width Timing Belt (Pack of 5pcs)

Specifications:
Number of tooth: 16T
Bore Diameter: 5mm
Net Weight: 3g/pcs
Material: Aluminum

Package Included:
5*20T GT2 Timing Belt Pulley

Product Features

  • Use for GT2 6mm Wide Timing Belt
  • Number of tooth: 16T
  • Bore Diameter: 3mm
  • Net Weight: 3g/pcs
  • Widely used in milling machine, gear shaper, drilling machine, CNC engine lathe, hobbing machine or other machinery transmission occasions

Detailed Information available on our Homepage…

Aunifun 5Pcs 30MM Length Extruder 1.75mm Tube and 5Pcs 0.4mm Brass Extruder Nozzle Print Heads And 5Pcs Aluminum Heater Block Specialized for MK8 Makerbot Reprap 3D Printers

✿Specification of Extruder Tube:
Type : Nozzle Throat
Compatibility : 3D Printer
Outer Thread : M6
Nozzle Throat Outer Diameter:7mm
Nozzle Throat Inner Diameter:4mm
Teflon Pipe Inner Diameter : 2mm
Length : 30mm
Filament Diameter : 1.75mm
Material : Stainless Steel

✿Specification of Brass Nozzle:
Type :0.4mm Extruder Brass Nozzle Print Head
Color: Golden
Material: brass
Size: 5*13mm
Input Diameter: 1.75mm
Output Diameter: 0.4mm
Compatible: compatible with all 1.75mm PLA ABS printer.

✿Specification of Heater Block:
Dimensions: 20*20*10mm(LxWxH)
Net Weight: 7g/pcs
Inner hole for set screw: M6 and M3 (heat pipe and thermocouple)
Heater Mounting Hole: 6mm diameter
Thermocouple Mounting Holes:3mm diameter
Suitable for Makerbot printer

Package Including:
5 x 3D Printer 30mm length 1.75mm Nozzle Inputting Tube( for MK8 Makerbot Reprap Prusa I3 3D Printer)
5 x 3D Printer 0.4mm Extruder Brass Nozzle Print Head
5 x Aluminum Heater Block

Attention: Small parts, keep away from children!!!

Product Features

  • ✿✿✿ Made of solid aluminum material, durable in use.
  • ✿✿✿ Nozzle Throat: Outer Thread – M6; Inner Diameter – 2mm; Length – 30mm; Filament Diameter – 1.75mm; Material – Stainless Steel.
  • ✿✿✿ 0.4mm Extruder Brass Nozzle Print Head: Color – Golden; Material – copper (brass); Size – 5*13mm; Input Diameter: 1.75mm; Output Diameter: 0.4mm.
  • ✿✿✿ Nozzle Throat and Nozzle Print Head compatible with all 1.75mm PLA ABS 3D printer.
  • ✿✿✿ Heater Block Inner hole for set screw: M6 and M3 (heat pipe and thermocouple)

Detailed Information available on our Homepage…