For Arduino Professional 3D printer CNC Kit,Longruner GRBL CNC Shield +UNO R3 Board+RAMPS 1.4 Mechanical Switch Endstop+DRV8825 A4988 GRBL Stepper Motor Driver with heat sink+Nema 17 Stepper Motor

CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino.
GRBL 0.9 compatible.
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13).
2 x End stops for each axis (6 in total).
Coolant enable.
Compatible with A4988 or DRV8825 stepper driver.
Runs on 12-36V DC.

DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware).

Nema 17 Stepper motor Specification:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g

Mechanical Endstop Connection Description:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles.
Length of Cable: 70 cm

Great Package Includes:
1 x CNC Shield Board
1 x Longruner UNO R3 Board
1 x 1.5m USB cable for R3 Board
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
3 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
4 x DRV8825 Stepper Motor Driver
4 x Aluminum heatsink w/ 3M tape backing
12x M3 Screws for bracket of stepper motor

Product Features

  • Latest CH340G CNC Shield expansion board Version 3.0 for Arduino.
  • Longruner UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable.
  • 4pcs DRV8825 Stepper Motor Driver with Heat Sinks.
  • 3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with Mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12pcs M3 Screws.
  • 3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable.

Click Here If You Need More Detailed Info…

Quimat Arduino CNC Shield Contoller Kits for 3D Printer,CNC Shield V3.0 + UNO R3 Board + Nema 17 Stepper Motor + A4988 Stepper Motor Driver + Heat Sinks,Perfectly Compatible with GRBL

CNC Shield V3.0 features:
Latest Arduino CNC Shield Version 3.0.
GRBL 0.8c compatible.(Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
4-Axis support(X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis(6 in total), Spindle enable and direction Coolant enable

Stepper drivers
Uses removable Pololu A4988 compatible stepper drivers.
Jumpers to set the Micro-Stepping for the stepper drivers.

Compact design.
Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)

Stepping Motor
The most popular Nema 17 model with 1.8 deg. step angle (200 steps/revolution)
0.4A rated current/phase, allowing for a holding torque of 26Ncm(36.8oz.in)
Connection:Black(A+), Green(A-), Red(B+), Blue(B-)

Stepping Motor Specification:
* Cable length: 11.8 inches
* Phase Resistance: 30ohms
* Inductance: 37mH+/-20%(1KHz)
* Frame Size: 42 x 42mm
* Body Length: 34mm
* Shaft Diameter: 5mm
* Front Shaft Length: 20mm
* D-cut Length: 15mm
* Number of Leads: 4
* Lead Length: 300mm
* Weight: 230g

Kit list:
1x CNC Shield V3.0
1x Keyestudio UNO R3 board
4x A4988 driver
1x USB cable
1x Nema 17 stepping motor

Product Features

  • CNC Shield V3.0 Features – Latest Version 3.0, GRBL 0.8c compatible, 4 Axis supported and 2 end stops for each axis.
  • Compact design – Stepper motors can be connected with 4 pin molex connectors or soldered in place.
  • Stepper Drivers – Uses removable Pololu A4988 compatible stepper drivers, jumpers to set the Micro-Stepping for the stepper drivers
  • Stepping Motor Included – Nema 17 model, holding torque of 26Ncm(36.8oz.in), 12V/0.4A and 1.8 deg.step angle(200 steps/rev)
  • Technical support – Our technical support team is on standby to provide solutions to your questions, please feel free to contact us.

Click Here If You Need More Detailed Info…

Wangdd22 3D Printer Parts 100Kohm NTC3950 Thermistors with Cable for 3D Printer Reprap Mend RAMPS 1.4 A4988 MK2B Heatbed(Pack of 10)

Specifications:

Negative temperature coefficient (NTC) thermistor
R @ 25: K100K-1%B25 / 50: K3950-1%
Element: thermistor type MJB2

Characteristics:

Resistance value: R (25 ° C) = 100K ± 1%
Resistance tolerance:± 1%
B value R25/50:3950k
Operating temperature range:-40° C ~+ 300 ° C
Temperature coefficient of resistance:-2 ~ -5% ° C
Maximum rated power:45mW
Dissipation power coefficient:>5mW/° C
Thermal time constant:≤7S

Colour:Milky white
Line length:1m

Package Includes:
10Pcs 100K temperature sensor

Product Features

  • High sensitivity and quick response;
  • Compact structure, easy installation;
  • Wide temperature range, good stability, high reliability;
  • Teflon wire is twice thicker than other similar products in the market. It is not easy to be break off;
  • It adopts white high temperature Teflon wire, resistant to high temperatureof 200 degrees;

Visit The Website For More Information…

[Sintron] 3d Printer Kit , Ramps 1.4 + Mega 2560 + 5pcs A4988 Stepper Driver w/ Heatsink + LCD 12864 Smart Controller + 3 Pcs End Stop + Mk2b Heat Bed + 2 Pcs Pulley + 2m Gt2 Belts for Reprap Prusa i3

Overview:

This kit is a good start for starter to build your own 3D printer. basically once you get the electronic parts done. then later it would be more easier to complete the rest parts.and yes, this is almost all the electronics you need for your 3D Printer.(except motors and extruder hotend)
If you are not sure what you need to complete your 3d printer project, please feel free to ask. We not just sell them, we also provide professional after-sales service, We will offer you a detailed tutorials including project introduction and their source codes. so welcome to discuss with us, we will try to do technical support as much as we can.

(1)3D Printer Controller RAMPS 1.4 – You can check:https://www.amazon.com/dp/B06WP5DDP1

(2)Mega 2560 R3 – You can check:https://www.amazon.com/dp/B00E94CGTQ

(3)LCD 12864 Graphic Smart Display Controller – You can check:https://www.amazon.com/dp/B00L72FAZU

(4)A4988 Stepper Motor Driver with Heatsink – You can check:https://www.amazon.com/dp/B00JXGT1G6

(5)Mechanical Endstop Switch – You can check: https://www.amazon.com/dp/B00OCFEZ1O

(6)2M GT2 Belt + 2 pcs GT2 20 Tooth Pulleys – You can check: https://www.amazon.com/dp/B00OFUZSP8

(7)MK28 Heatbed:This is the latest version of MK2B,100% compatible with all Prusa and Mendel 3d printer variants.

Package List:

(1)3D Printer Controller RAMPS 1.4 x1
(2)Mega 2560 R3+USB Cable x1
(3)A4988 Stepper Motor Driver with Heatsink x5
(4)LCD 12864 Smart Controller x1
(5)MK28 Heatbed with Thermistor and High Temp Wire x1
(6)Mechanical Endstops x3
(7)2M GT2 Belt+20 Tooth Pulleys x2
(8)Smart Adapter x1
(9)30cm Cable x2
(10)Storage Box x1

Product Features

  • (1) 3D Printer Controller RAMPS 1.4 x 1 + Mechanical Endstops x 3
  • (2) Arduino-Compatible Mega 2560 R3 With USB Cable x 1
  • (3) A4988 Stepper Motor Driver With Heatsink x 5
  • (4) LCD 12864 Graphic Smart Display Controller Kit x 1
  • (5) MK28 Heated Bed with Thermistor and High Temp Wire x 1

Click Here If You Need More Detailed Info…

Professional 3D printer CNC Kit for arduino, Kuman GRBL CNC Shield +UNO R3 Board + RAMPS 1.4 Mechanical Switch Endstop + DRV8825 A4988 GRBL Stepper Motor Driver with heat sink + Nema 17 Stepper Motor

CNC Shield Board:
Latest CNC Shield Version 3.0 for arduino
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC

DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It’s not arduino official board but it’s compatible with all arduino software and hardware)

Nema 17 Stepper motor Specification:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg.
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g

Mechanical Endstop Connection description:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles
Length of Cable: 70 cm

Package Contents:
1 x CNC Shield Board
1 x Kuman UNO R3 Board 
4 x DRV8825 Stepper Motor Driver
4 x Aluminum heatsink w/ 3M tape backing
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
12x M3 Screws for bracket of stepper motor
3 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
1 x 1.5m USB cable for R3 Board

Product Features

  • Latest CH340G CNC Shield expansion board Version 3.0 for Arduino
  • Kuman UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable
  • 4pcs DRV8825 Stepper Motor Driver with heat sinks
  • 3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12 pcs M3 Screws
  • 3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable

Click Here If You Need More Detailed Info…