KINGPRINT 3D Printer Controller Board MKS TFT32 3.2-Inch Full-Color Touch Screen for 3D Printer

Specification:

Weight: 91g 1. Support for power continued to fight, to save power. 2. Support blanking detection. 3. The boot logo and all buttons can design their own interfaces. 4. Increase the custom function button. 5. Support full English interface. Package Included:

1 * MKS-TFT32

Product Features

  • 3.2 inch color touch screen, support U disk and SD card.
  • Reserved Wifi interfaces, increasing Wifi interface board supports Wifi.
  • To provide continuous software upgrades, easy to upgrade.
  • Can be used on creating customer base launched MKS series motherboard.
  • The master program without modification, plug and play, support Marlin, Repetier, Smoothieware firmware.

Visit The Website For More Information…

KINGPRINT 3D Printer MKS Gen V1.4 Controller Board Mega 2560 R3 Motherboard RepRap Ramps1.4 Compatible with USB

-Can accept 24V input power under the same system can be hot-bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems.
-Tthe firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4.
– Can be connected to the control panel and 12864LCD Ramps1.4,2004LCD control panel.(Can’t be sure to match all of stype of 12864LCD and 2004LCD )
– Reserved for motor pulse and direction output ports for easy plug-in high-current To add a large current (eg 2A, 5A) motor drive circuit.
-Reserved Ramps1.4 on Servos, AUX-1, AUX-2 interface that provides three 5V output, three 12V outputs.

Specification:

Type: MKS Gen V1.4 control board Mega 2560
Name: MKS Gen V1.4 control board
Weight: 118g
Application: 3D Printer Part
Weight: 118g

Package Included:

1* MKS Gen V1.4 Control Board

Product Features

  • Mega 2560 and ramps1.4 set on a board, to solve complicated Ramps1.4 combination of interfaces, the problem of failure prone.
  • Replace the motor drive, drive and support 4988 8825 drive.
  • The circuit board with high-quality 4-layer, heat and made a special optimization; ramps are 2 shelves.
  • Using high-quality MOSFET, and better heat dissipation.
  • Using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.

Visit The Website For More Information…

HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…

Inkbird Dual Stage Digital Temperature Controller Fahrenheit Thermostat with Sensor for 3D Printer,Freezer,Fridge,Hatching ect


Fahrenheit and Celsius Display Can Be Choose
Temperature Calibrating, Refrigerating control output delay protection
Control the Temperature by Setting the Temperature Set Value and the Difference Value
Alarm When Temperature Exceeds the Limit or When Sensor Error
2 Relays, Switch Between Cooling and Heating Modes

Technical Parameter:
Output: 2 Relays
Temperature Measuring Range: -50~210 oF / -50 oC-99 oC
Resolution: 0.1 oF / 0.1 oC
Accuracy: ±1 oF(-50 oF -160 oF)/ ±1 oC(-50 oC -70 oC) Power Supply: 110VAC 50Hz/60Hz
Power Consumption: 3W
Sensor: NTC Sensor
Relay Contact Capacity: Cooling (10A/250VAC)/ Heating (10A/250VAC);
Ambient Temperature: 0 oC-60 oC
Storage Temperature: -30 oC-75 oC
Relative Humidity: 20-85% (No Condensate)

Package Content:
1x Temperature controller ITC 1000 110V
1x 7.87″ SENSOR
1x Muanal

Product Features

  • It does indeed read in deg F.
  • Can control both heating and cooling output
  • Has an alarm to indicate sensor failure or high temperature
  • Highly accurate and reliable temperature controller
  • Be more user friendly than the STC-1000

Detailed Information available on our Homepage…

3D Printer Engraving Expansion Board Kit Controller CNC Shield V4+Nano 3.0 Board+A4988 Driver with USB Cable for Arduino

Why this kit?

CNC Shield V4+Nano 3.0 Board+A4988 Driver as a driver expansion board, can be used for engraving machines, 3D printer, and It is a total of three slots, can drive three A4988 stepper motor.

Specifications:

V4 Board Size: 7.2 x 5.9cm / 2.83 x 2.32″

Improved Nano Board Size: 4.3 x 1.8cm / 1.69 x 0.7″

Driver Size: 2 x 1.5cm / 0.78 x 0.59″

Heat Sink Size: 0.8 x 0.8cm / 0.31 x 0.31″

Package:

1 x CNC Shield V4.0

1 x Nano 3.0 Board

3 x A4988 Drivers

1 x USB Cable

3 x Heat Sinks

 

Note:

 WE DO NOT PROVIDE ANY TECHNICAL HELP. Thank you for your understanding.

Product Features

  • – It is a flexible set, with 3 axis stepper motor driver, compatible with Arduino and most shields designed for the Arduino micro-drive laser engraving machine, three-axis CNC engraving machine
  • – Power DC5V interface and 7.5-12V voltage input, compatible with GRBL for easy service, part replacement, upgrade-ability and expansion
  • – Easy to operate: 2A can be controlled within the two-phase four-wire stepper motor, simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started
  • – Released the digital IO interface and the I2C interface, easy to connect to other modules, such as ENDSTOP, LCD I2C or other I2C module
  • – Simple step and direction control interface, taking anti-static measures before you use the A4988 modules in case of short-circuit

Visit The Website For More Information…