EasyULT 6 Pack Makerbot Designed Mechanical Endstop Kit Is For 3D Printer Makerbot Prusa Mendel RepRap CNC Arduino Mega 2560 1280

Connection Description:
Red line connecting VCC (ramps of +)
Connect the black wire GND (ramps of -)
Green Line connection SIGNAL (ramps in s)
High quality connection, using 22AWG wire
Inside of copper wire is very thick, can be resistant to current 2A or 300V voltage
A wide range of temperatures, up to 80 degrees
Tips: In normal circumstances, the system must be configured to three mechanical
Length of Cable: 70 cm
Quantity: 6 set

Product Features

  • Mechanical Endstop perfect for any 3D printer (Including Prusa Mendel i2, Prusa i3, MendelMax, Rostock etc…) also for use on CNC machines and other electronic applications.
  • Customized high quality connection, using 22AWG wire, copper wire inside is very thick, can be resistant to current 2A, 300V voltage. An insulating layer over a wide range of temperatures, up to 80 degrees.
  • Pros: Easy to install, the more common styles.
  • Not easy to pull off, easy to install
  • tips: Under normal circumstances, the system must be configured to at least three mechanical switches.

Click Here If You Need More Detailed Info…

[REPRAPGURU] 12864 LCD Full Graphic Smart Display Controller for RepRap RAMPS 1.4 3D Printer Mendel Prusa Arduino Mega Pololu Shield Arduino RepRap

This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included.
After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.
Features
(1) Using a large screen 12864LCD.
(2) With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.
(3) Product comes encoder parameter adjustment can be achieved, and the file selection print.
(4) Plug and play on the RAMPS, but need to modify the firmware to support.
Package List Includes
(1) LCD 12864 Smart Controller x 1
(2) Smart Adapter x 1
(3) 30cm FC Cable x 2

Product Features

  • USA Customer Support
  • Print from SD card
  • Plug and play on the RAMPS 1.4, (with supporting firmware)
  • Using a larger screen 128X64

Detailed Information available on our Homepage…

8pcs GT2 16T Bore 5mm Timing Pulley+ 5 Meters Belt For RepRap Prusa Mendel 3D Printer GT16 Teeth

8pcs GT2 16T Bore 5mm Timing Pulley+ 5m Belt For RepRap Prusa Mendel 3D Printer

Product Features

  • GT2 Pulley : Teeth Number :16, Flange Double, Material Aluminium
  • Teeth Pitch 2mm , Diameter of Bore 5mm
  • Teeth Width 7.5mm(Very Suitable and good for 6mm synchronous belt)
  • GT2 Belt: Color Black, Pitch 2mm, Width 6mm
  • Material Fiber Reinforced Rubber, Length 5Meters

Detailed Information available on our Homepage…

Prusa Mendel Hardware Kit fastener Set Nut Washer Bolt Grub Screw for 3D Printer Waynetool

This is a fastener set for a Reprap Prusa Mendel i2 3D printer DIY kit. All screws are Phillips Head. Much easier to work with in tight spaces than hex head bolts. Package includes: M2.5 x 16 stainless steel Phillips Head Screws:6pcs M3 x 10 stainless steel Phillips Head Screws:20pcs M3 x 20 stainless steel Phillips Head Screws:50pcs M3 x 30 stainless steel Phillips Head Screws:5pcs M3 x 40 stainless steel Phillips Head Screws:5pcs M3 x 50 stainless steel Phillips Head Screws:4pcs M2.5 stainless steel Hex Nuts: 6pcs M3 stainless steel Hex Nuts: 50pcs M8 stainless steel Hex Nuts: 50pcs for frame assembly M2.5 stainless steel Flat Washers: 6pcs M3 stainless steel Flat Washers:50pcs M8 stainless steel Flat Washers:50pcs for frame assembly M3 x 8 stainless steel Grub Screws:3pcs M8 x 20 Grub Screws: 1pc M8 x 50 Grub Screws: 1pc Item will be shipped by airmail within 24 hours after full payment is received.

Visit The Website For More Information…

Happisland Drill Bits for 3D Printer Nozzle Cleaning Makerbot Mendel Reprap Pack of 10PCS:0.2mm 0.3mm 0.4mm 0.5mm 0.6mm,Each 2 Pcs

Pack of 10 PCS:0.2mm 0.3mm 0.4mm 0.5mm 0.6mm,Each 2 Pcs

Product Features

  • Pack of 10 PCS:0.2mm 0.3mm 0.4mm 0.5mm 0.6mm,Each 2 Pcs
  • Conveniently colored silicone grip gasket for spinning bits by hand
  • Color is random
  • Note:Don’t use the drill to clean until the nozzle is heated to above 200 degrees
  • Any question,pls feel free to contact us.

Detailed Information available on our Homepage…