ARQQ Heat Bed Mosfet Tube Hot Bed Power Module Expansion for 3D Printer Heating Bed Accessories(Pack of 2)

Details: Dimensions: 60*50mm
Net Weight: 40g
Color:Black
Max Current: 25A(Enhance heat dissipation)
Wire’s color is random

Summary:
1. Remove basically all ouside screws for your anet a8 control box
2. Take pictures of existing board wiring
3. Unscrew two large 12/14GA wires on the board labeled “hot bed”
4. Screw these two wires into the new mosfet board labled “hot bed”
5. Connect the small jumper wires (white) to the control board where you just removed the two wires and screw them down. Note the polarity on each board. Match (+) to (+) and (-) to (-)
6. FInd 2x 6-8″ pieces of 12 or 14 AWG wire. Most cheap extension cords are 16AWG (too thin). Your local home depot / menards / ace will have this as cut-to-length
7. Run one of the 6″ wires to the power supply (+), screw in; and the other side to the (+) DC IN on the new mosfet board. Repeat for the negative wire (-) to (-)
8. Many people use velcro to secure the new board to the top of the control box. Others print off a holder from thingiverse
9. Put everything back together
10. When complete, you’ll see a blue light activate for signal from inside the box when the bed heater is activated by the control board

Package Included:
2xHot bed MOS Tube Power Module Expansion

Product Features

  • Work with anet a8 3d printer heat bed
  • Completely solve the hot bed power is too large and the load current issue
  • Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working
  • General Add-on Heated Bed Power Expansion Module
  • Note: Any issue please contact us before, we will always here to help!

Detailed Information available on our Homepage…

HESAI 3D Printer Kit Smart Parts RAMPS 1.4 Controller Control Panel LCD 2004 Module Display Monitor Motherboard Blue Screen

Description:

The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.4 board using “smart adapter” included.

This panel connect your RAMPS 1.4, you do not need your computer, your SD card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller. 3D design print without a computer, just use the G code design stored on the SD card.

Package List:

1x LCD 2004 Smart Controller

1x Smart Adapter

2x FC Cable

Product Features

  • Popular RepRap 3D Printer LCD Controller and SD Card Reader
  • Included adapter for RAMPS 1.4 board
  • Fully supported by Marlin firmware
  • With Smart LCD Controller you can print 3D designs without USB connection to your computer

Visit The Website For More Information…

ARQQ Heat Bed Mosfet Tube Hot Bed Power Module Expansion for 3D Printer Heating Bed Accessories

Details: Dimensions: 60*50mm
Net Weight: 40g
Color:Black
Max Current: 25A(Enhance heat dissipation)
Wire’s color is random

Summary:
1. Remove basically all ouside screws for your anet a8 control box
2. Take pictures of existing board wiring
3. Unscrew two large 12/14GA wires on the board labeled “hot bed”
4. Screw these two wires into the new mosfet board labled “hot bed”
5. Connect the small jumper wires (white) to the control board where you just removed the two wires and screw them down. Note the polarity on each board. Match (+) to (+) and (-) to (-)
6. FInd 2x 6-8″ pieces of 12 or 14 AWG wire. Most cheap extension cords are 16AWG (too thin). Your local home depot / menards / ace will have this as cut-to-length
7. Run one of the 6″ wires to the power supply (+), screw in; and the other side to the (+) DC IN on the new mosfet board. Repeat for the negative wire (-) to (-)
8. Many people use velcro to secure the new board to the top of the control box. Others print off a holder from thingiverse
9. Put everything back together
10. When complete, you’ll see a blue light activate for signal from inside the box when the bed heater is activated by the control board

Package Included:
1xHot bed MOS Tube Power Module Expansion

Product Features

  • Work with anet a8 3d printer heat bed
  • Completely solve the hot bed power is too large and the load current issue
  • Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working
  • General Add-on Heated Bed Power Expansion Module

Detailed Information available on our Homepage…

Jili Online 3D Printer Part Material Detection Module with Wire for 1.75mm Filament Module Monitor Sensor

Description:

– Wear-resistant copper sets added in both the inlet and outlet to effectively extend the product life. Wiring: Connect the module to the M-sensor port on the motherboard.
– Used for Lerdge board: When there is material in, the green light in the module keeps lighting. when the material is exhausted, the green light goes off,and the motherboard executes the pause command operation, after the replacement of the material, can continue to print.
– Used with other motherboards: The material detection module uses the level transition detection method.
– When with material in, the detection level signal should be high, and when no material, the material port level signal goes low.
– When the system detects a determined transition from high to low level, it will regard it as the material exhausted, then the board executes the pause command operation, and after the replacement of the material, it will continue to print.

Specification:

– Board size: 38*30*13mm/1.50*1.18*0.51inch

Package Includes:

1 Piece Material detection module with cable.

Product Features

  • Wear-resistant copper sets added in both the inlet and outlet to effectively extend the product life. Wiring: Connect the module to the M-sensor port on the motherboard.
  • Used for Lerdge board: When there is material in, the green light in the module keeps lighting. when the material is exhausted, the green light goes off,and the motherboard executes the pause command operation, after the replacement of the material, can continue to print.
  • Used with other motherboards: The material detection module uses the level transition detection method.
  • When with material in, the detection level signal should be high, and when no material, the material port level signal goes low.
  • When the system detects a determined transition from high to low level, it will regard it as the material exhausted, then the board executes the pause command operation, and after the replacement of the material, it will continue to print.

Visit The Website For More Information…

HESAI 3D Printer Controller Kit for Arduino Mega 2560 R3 Board + RAMPS 1.4 Control Panel + LCD 12864 Motherboard Display + 5pcs DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink

MEGA 2560 R3 Board

The Mega is 100% compatible with Arduino and most shields designed for the Arduino

The chip is Atmega2560-16au and Atmega16u2, same with the official version.

Improved and expert version: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.

Stronger RESET circuit.

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

RAPMS 1.4 Controller

Fully assembled & tested, no soldering required

Designed to fit the entire electronics needed for a RepRap in one small package for low cost.

Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.

A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.

Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

LCD 12864

Using a large screen 12864LCD.

With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.

Product comes encoder parameter adjustment can be achieved, and the file selection print.

Plug and play on the RAMPS, but need to modify the firmware to support.

Package List:

1x MEGA 2560 R3 Board

1x RAMPS 1.4 Controller

1x LCD 12864

5x DRV8825 Driver

5x Heat Sink

1x Screwdriver

Product Features

  • Fully assembled & tested, no soldering required
  • Designed to fit the entire electronics needed for a RepRap in one small package for low cost.
  • Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
  • A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
  • Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.

Click Here If You Need More Detailed Info…