Wangdd22 3D Printer Kit 14pcs/lot Cables Complete Wiring Cables Set For RAMPS 1.4 Endstops Thermistors Motor Dupont Cable

Use these cables enjoy your all of your electronic projects,Such as 3D printers, Arduino motherboards, modules and so on.

Package includes:
3pcs 70cm 2pin F-F Wires
6pcs 70cm 3pin F-F Wires
5pcs 70cm 4pin F-F Wires

Product Features

  • Cable Length:70cm.
  • Cable Attributes: Female to Female.
  • Product Color: Red, Black, Green, Blue.
  • 1 Set=3pcs 2pin+5pcs 4pin+6pcs 3pin cable
  • Product uses: Such as 3D printers, Arduino motherboards, modules and so on

Click Here If You Need More Detailed Info…

HESAI DRV8825 Stepstick Stepper Motor Driver Module + Heat Sink for RepRad 3D Printer RAMPS 1.4 Controller Replace A4988 (Pack of 5 pcs)


The DRV8825 stepper motor driver carrier board TI DRV8825 micro bipolar stepper motor drive is a breakthrough. The module has a pinout and interface with our A4988 stepper motor driver carrier is almost the same, so it can be used as a better performance of the pull-down menu board replacement in many applications. DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step). It uses 8.2 – 45 V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling).


A simple steps and direction control interface

Six different steps resolutions: full step, half step, 1/4-step1/8-step1/16-step, 1/32-step

CAN interface directly with 3.3 V and 5 V systems

Over-temperature thermal shutdown, overcurrent shutdown, undervoltage lockout

Short to ground short circuit load protection

4 Layer 2 oz copper PCB, in order to improve heat dissipation

Exposed solder ground below the bottom of the driver IC on the printed circuit board pad

Module size, pin and interface matching A4988 stepper motor driver operators in many ways

Adjustable current control lets you set a potentiometer, which lets you use the stepper motor\’s rated voltage or more, in order to achieve a higher rate of maximum output current step

Intelligent chopping control automatically selects the correct current decay mode (fast decay or slow decay)

Maximum 45 V supply voltage

Built-in voltage regulator (the need for any external logic supply voltage)

Package List:

5x DRV8825 Stepper Motor Driver

5x Heatsink

1x Screwdriver

Product Features

  • This DRV8825 Stepper Motor Driver Module is upgrade of A4988
  • Simple step and direction control interface
  • 4-layer, 2 oz copper PCB for improved heat dissipation
  • Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
  • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates

Visit The Website For More Information…

CHENBO(TM) 5 x Endstop Mechanical Limit Switches 3D Printer Switch for RAMPS 1.4

Red line connecting VCC (ramps of +)
Connect the black wire GND (ramps of -)
Green Line connection SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Pros: Easy to install, the more common styles
Length of Cable: 70 cm

Product Features

  • Endstop mechanical limit switches use 3D printer switch RAMPS 1.4
  • 3 pin connectivity
  • Compatible with RAMPS 1.4, CNC and other 3D printer controllers
  • 70cm Length Wire

Detailed Information available on our Homepage…

HESAI 3D Printer Kit Smart Parts LCD 12864 Display Monitor Motherboard Blue Screen Module for RAMPS 1.4 Controller Control Panel


This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included. After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.

Package List:

1x LCD 12864 Smart Controller

1x Smart Adapter

2x FC Cable

Product Features

  • Using a large screen 12864LCD
  • With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing
  • Product comes encoder parameter adjustment can be achieved, and the file selection print
  • Plug and play on the RAMPS, but need to modify the firmware to support

Visit The Website For More Information…

KINGPRINT 3D Printer Mechanical Limit Switch with 70cm cable for 3D Printer Ramps 1.4 (Pack of 5pcs)

Packing: PE bag
Type: Endstop switch
Product Name: Mechanical Endstop
Color: showed in picture
Condition: 100% Brand New
Type : integrated circuit
Usage: 3D Printer parts
Material: Aluminum

Connection Description:

Red line connecting VCC (ramps of +)

Connect the black wire GND (ramps of -)

Green Line connection SIGNAL (ramps in s)

Package Included:

5* Endstops
5* 3PIN 70CM Cable For Endstop

Product Features

  • EASY USE— The interface is simple, it’s not easy to break.
  • FOR REPRAP 3D PRINTER OR CNC MACHINES—which are supported by RepRap Electronics,
  • RAMPS 1.4 and other popular RepRap boards.
  • OUR PROMISE—High quality assurance, comprehensive after-sales service.

Visit The Website For More Information…