EasyULT 6 Pack Makerbot Designed Mechanical Endstop Kit Is For 3D Printer Makerbot Prusa Mendel RepRap CNC Arduino Mega 2560 1280

Connection Description:
Red line connecting VCC (ramps of +)
Connect the black wire GND (ramps of -)
Green Line connection SIGNAL (ramps in s)
High quality connection, using 22AWG wire
Inside of copper wire is very thick, can be resistant to current 2A or 300V voltage
A wide range of temperatures, up to 80 degrees
Tips: In normal circumstances, the system must be configured to three mechanical
Length of Cable: 70 cm
Quantity: 6 set

Product Features

  • Mechanical Endstop perfect for any 3D printer (Including Prusa Mendel i2, Prusa i3, MendelMax, Rostock etc…) also for use on CNC machines and other electronic applications.
  • Customized high quality connection, using 22AWG wire, copper wire inside is very thick, can be resistant to current 2A, 300V voltage. An insulating layer over a wide range of temperatures, up to 80 degrees.
  • Pros: Easy to install, the more common styles.
  • Not easy to pull off, easy to install
  • tips: Under normal circumstances, the system must be configured to at least three mechanical switches.

Click Here If You Need More Detailed Info…

Witbot MK10 M7 0.4mm Extruder Upgrade Stainless Steel Wear Resistant Nozzle for Makerbot RepRap 3D Printer (Pack of 5pcs)

Specifications:
Bore Diameter: 0.4mm
Size: 13mm * 9mm
Net Weight: 4g/pcs
Material: Stainless Steel

Package Included:
5*MK10 Stainless Steel Nozzle

Product Features

  • 100% brand new and high quality
  • This product is dedicated on MK10 Extruders
  • The nozzle material use the national standard copper
  • Compare with the non-national standard copper, it have obvious differences,our nozzle’s thermal conductive performance is better than the non-national standard copper
  • Hard coating improves service life and reduces down time

Click Here For More Information

Anet 12864 LCD Smart Display Screen Controller Module with Cable for RAMPS 1.4 Arduino Mega Pololu Shield Arduino Reprap 3D Printer Kit Accessory

Features:
12864 LCD smart controller for 3D printer.
Supports for RAMPS 1.4 control board.
Built-in encoder allows you adjusting the parameter and selecting file to print.
Large size screen, clear white characters with blue backlit.
Tuning and press the round button to control, with buzzer for reminding, a reset button, easy for operation.

Specifications:
Brand: Anet
Model: 12864
Screen: LCD
Screen Size: 3in
Item Weight: 139g / 4.9oz
Package Size: 18 * 10 * 3cm / 7.1 * 3.9 * 1.2in
Package Weight: 143g / 5.0oz

Package List:
1 * 2004 LCD Screen
2 * Cable

Product Features

  • 12864 LCD smart controller for 3D printer.
  • Supports for RAMPS 1.4 control board.
  • Built-in encoder allows you adjusting the parameter and selecting file to print.
  • Large size screen, clear white characters with blue backlit.
  • Tuning and press the round button to control, with buzzer for reminding, a reset button, easy for operation.

Click Here If You Need More Detailed Info…

Anycubic NTC 3950 100K Thermistor with 1 Meter Wiring and Female Pin Head for RepRap 3D Printer Heatbed or Hot End Pack of 5PCS

Specification:

– For 3D printers: use TEMP_SENSOR 11 in Marlin firmware

– Small Size: 1.25mmx2.0mm glass bead

– High accuracy: 1%

– Resistance value at 25°C=100K

– Wiring insulation: high temperature teflon/PTFE

– Wiring length: 1 meter

Package List:

5* NTC 3950 100k thermistor with female head

Product Features

  • Conviniently pre-wired with 1 meter long high temperature PTFE insulated wiring
  • Use it with heated bed or extruder
  • Temperature sensor 100KΩ accuracy of ± 1%
  • Pack of 5PCS

Click Here For More Information

[Sintron] 3d Printer Kit , Ramps 1.4 + Mega 2560 + 5pcs A4988 Stepper Driver w/ Heatsink + LCD 12864 Smart Controller + 3 Pcs End Stop + Mk2b Heat Bed + 2 Pcs Pulley + 2m Gt2 Belts for Reprap Prusa i3

Overview:

This kit is a good start for starter to build your own 3D printer. basically once you get the electronic parts done. then later it would be more easier to complete the rest parts.and yes, this is almost all the electronics you need for your 3D Printer.(except motors and extruder hotend)
If you are not sure what you need to complete your 3d printer project, please feel free to ask. We not just sell them, we also provide professional after-sales service, We will offer you a detailed tutorials including project introduction and their source codes. so welcome to discuss with us, we will try to do technical support as much as we can.

(1)3D Printer Controller RAMPS 1.4 – You can check:https://www.amazon.com/dp/B06WP5DDP1

(2)Mega 2560 R3 – You can check:https://www.amazon.com/dp/B00E94CGTQ

(3)LCD 12864 Graphic Smart Display Controller – You can check:https://www.amazon.com/dp/B00L72FAZU

(4)A4988 Stepper Motor Driver with Heatsink – You can check:https://www.amazon.com/dp/B00JXGT1G6

(5)Mechanical Endstop Switch – You can check: https://www.amazon.com/dp/B00OCFEZ1O

(6)2M GT2 Belt + 2 pcs GT2 20 Tooth Pulleys – You can check: https://www.amazon.com/dp/B00OFUZSP8

(7)MK28 Heatbed:This is the latest version of MK2B,100% compatible with all Prusa and Mendel 3d printer variants.

Package List:

(1)3D Printer Controller RAMPS 1.4 x1
(2)Mega 2560 R3+USB Cable x1
(3)A4988 Stepper Motor Driver with Heatsink x5
(4)LCD 12864 Smart Controller x1
(5)MK28 Heatbed with Thermistor and High Temp Wire x1
(6)Mechanical Endstops x3
(7)2M GT2 Belt+20 Tooth Pulleys x2
(8)Smart Adapter x1
(9)30cm Cable x2
(10)Storage Box x1

Product Features

  • (1) 3D Printer Controller RAMPS 1.4 x 1 + Mechanical Endstops x 3
  • (2) Arduino-Compatible Mega 2560 R3 With USB Cable x 1
  • (3) A4988 Stepper Motor Driver With Heatsink x 5
  • (4) LCD 12864 Graphic Smart Display Controller Kit x 1
  • (5) MK28 Heated Bed with Thermistor and High Temp Wire x 1

Click Here If You Need More Detailed Info…